Media Land Rover

Replace Range Rover Evoque Door Locks Mechanisms (Problems Solved) Motor Verso

Replace Range Rover Evoque Door Locks

If you are a Land Rover Range Rover Evoque owner, then it is a matter of time before you may need to consider replacing your doors’ lock mechanisms.

Range Rover Evoque Door Lock Problems

Unfortunately, over time the locking mechanisms begin to wear out and may no longer be capable of either locking or unlocking the doors of the vehicle. This can sometimes manifest as an intermittent fault which then grows over time to a complete failure.

Part List

We have looked around online to find who stocks these locks. There will change from time to time, but please see the below. Double check the part numbers etc for your exact car, model and trim.

Front Passenger Lock – Amazon

Front Driver Lock – Amazon

Rear Passenger – Amazon

Rear Driver Lock – Amazon

Pack of all 4 locks – Amazon

Solution –Replace Range Rover Evoque Door Locks

To resolve the problem, you should replace the locking mechanisms of the affected doors. You can either get a Land Rover specialist to do this for you, or you can do it yourself. I personally managed to carry out this task myself as an amateur mechanic, and it took me an average of one hour per lock, without rushing.

Here is the overview of the replacing process:


Get A Professional To Do The Job

If you don’t have time or the ability to do the work yourself. Call JMB Services on 0121 296 7820  – They can carry out the work using the original parts.

Location: Unit 8 Century Industrial Estate, Shady Lane, Great Barr, Birmingham, B44 9ER

Without Keyless Entry – Parts and Labour (Estimated cost)

With Keyless Entry – Parts and Labour (Estimated cost)


The Process

1) Remove The Door Card

The door card needs to be removed to allow access to the lock. Open the door. There are 4 screws to be removed (see Figure 1). Please note beforehand that all the screws are covered with plastic inserts that will need to be removed by either using a small thin screwdriver or a blade.

Once the screws have been removed, the door card then needs to be pried away from the door. There is a risk of damaging the paintwork here, so I would recommend using a selection of plastic lever bars.

Place a lever bar between the door card and the metal part of the door, then use two levers to force the door card’s clips out of the door’s holes. Work your way around the edge of the door, while being careful not to damage the clips. Please note that the card will be removed outwards from the door itself and does not need to be pulled up.

2) Disconnect The Cables

Once the door card has been removed, you will need to support it whilst you remove all the cables (see Figure 2). This can be done with one hand if needed, and you need to be careful not to break any of the connectors.

3) Remove The Inner Door Card

Before removing the inner section of the door card, there are two cables that need to be disconnected which are highlighted in yellow below (see Figure 3).

Next, you will need to remove the 12 screws around the edge of the inner card (Red).

Once removed, you will notice the card is held in place with a sticky seal. Once again, you will need to use a plastic lever tool to separate the two parts.

As it comes off, you will need to run the door handle cable through the trim and turn the inner door card downwards.

Once this is done, you can leave the card hanging. Be careful not to damage the exposed speaker.

4) Remove The Screws From The Lock

Before removing the screws, reach inside the door and disconnect the power connector from the lock.

Next, look at the end of the door. Where the locking mechanism sits, there will be 3 screws. Remove all 3 of these allowing the lock to hang only by the internal cables.

5) Disconnect the Cables and Remove the Lock

Depending on which door you are working on, there will be two or three cables to disconnect:

Removing the cables is very complicated work and difficult to explain. I would recommend using a torch inside the door to carefully examine how the cables are fitted, so you can safely remove them and refit the cables to the new lock. The cables need to be properly aligned to be disconnected and reconnected so please don’t hesitate to take your time.

6) Refit the New Locking Mechanism

Next up, simply repeat the procedure in reverse. I would advise reconnecting the door open cables first, before attaching the lock to the door again, as it is much easier to handle.

7) Testing the New Lock

Once everything has been reassembled, before shutting the door, make sure you check that the lock has been unlocked, otherwise you may risk damaging the lock or the door.

Check that it locks, deadlocks and unlocks without any issues.

Finally check all the switchgear that was disconnected (electric windows, mirrors, lighting and speakers etc).

How do you reset a Range Rover?

To reset the device, simultaneously press the Power on and Volume up button for 10 – 12 seconds
The device will power down and then automatically reboot
Device will now power on, perform and charge as expected

How do you manually lock a Range Rover Evoque?

The drivers side section of the lock has a small plastic part that can be removed open up a physical lock that you can turn.

Do Range Rovers lock automatically?

Drive-away locking automatically locks all of the doors when the vehicle reaches a set speed. This can be turned on and off.

How to Replace Range Rover Evoque Door Locks Mechanisms was last modified: by

Source: www.motorverso.com